Visonic POWERMASTER-10 Betriebsanweisung PDF herunterladen (Seite 38)

MENUS AND FUNCTIONS

D-303223 PowerMaster-10 / PowerMaster-30 User's Guide 37

C.6 Add / Delete Keyfob Transmitters

Each of the 8 PowerMaster-10 / PowerMaster-30 users may be provided with a portable keyfob transmitter to

exercise better, quicker and safer arming/disarming and other control functions. Each keyfob should be

assigned with a serial No. 1-8 (PowerMaster-10) / 1-32 (PowerMaster-30) and enrolled into the system

correspondingly.

Partition Option

∗

(For information about Partition option - see Appendix A)

If the Partition option is enabled in the control panel, each of the 32 keyfobs can be authorized by the Master

User to arm and disarm any combination, or all 3 partitions, irrespective of the authorization of its corresponding

user code.

♦ Here you can add (enroll) the 8 (PowerMaster-10) / 32 (PowerMaster-30) Keyfob transmitters and define

which of the 3 partitions

∗

each of the keyfob will be authorized to arm and disarm, or delete keyfobs as

required.



1. Before anything else, gather up all keyfob units you intend to enroll and make sure they all have

batteries installed and that they are active (the LED blinks upon pressing any of the buttons).

2. Carefully read the section titled "Additional Information" according to the indicated references

etc –

see table at end of this section.

A. To Add (Enroll) a Keyfob

Enter the USER SETTINGS menu, select the [KEYFOBS] option and press

the button to confirm.

The display will read [ADD NEW KEYFOB].

To enroll a new keyfob press

The display offers you two alternative methods to enroll a keyfob:

A: ENROLL NOW: Press and hold the AUX  button on the selected keyfob

until the LED is constantly on.

This procedure completes the enrollment.

4a.

☺ Go to step 5

If enrollment was successfully completed, a "Happy Tune" ☺ sounds and

the display reads [DEVICE ENROLLED] for a short duration and then changes

to read the keyfob's details. Continue to step 5.

4b.

B: ENTER ID (Pre-enrollment): Enter the 7-digit number that appears on

the keyfob sticker and then press to confirm. To complete the

enrollment procedure see note 6 in the Additional Information table below.

☺ Go to step 5

If a valid ID was entered, a "Happy Tune" ☺ sounds and the display reads

[ID ACCEPTED] for a short duration and then changes to read the keyfob's

details. Continue to step 5.

The display shows the allocated keyfob serial No (user No.), which is always

the first free number, and the keyfob's ID number; for example:

[F01:Keyfob] alternating with [ID No. 300-5786].

If you wish to assign the keyfob to another user, for example, "User No. 5", ",

∗

Refers to PowerMaster-30 only

ID No. 300

5786

F01:keyfob

ID ACCEPTED

ENTR ID:xxx

xxxx

ID No. 300

5786

DEVICE ENROLLED

ENROLL NOW or

ADD NEW KEYFOB

KEYFOBS

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 75 76

Kommentare zu diesen Handbüchern

Keine Kommentare

Visonic POWERMASTER-10 Betriebsanweisung Seite 38

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Visonic POWERMASTER-10