Visonic POWERMASTER-10 Betriebsanweisung PDF herunterladen (Seite 32)

5. PROGRAMMING

D-304762 PowerMaster-10/30 G2 Installer's Guide

Step 9



Step 10



Step 11

Enter Device Settings

[9]

Configure Device

Parameters

[10]

Continue or End

➯



Z10:DEV SETTINGS

Refer to device

datasheet in the device

Installation Instructions

for specific configuration

instructions.

To continue –

See  [11]



- Configuring New Devices

Location (name) setting:

[1]

To review or change the Location (name) setting, press the button, otherwise scroll to the next option.

[2]

To change the Location name, enter the menu and select the name from the "Location List" below. You can

assign additional custom names using the "06.CUSTOM NAMES" option in the Installer menu. See section 5.8.

Note: As a shortcut, press the 2 digit serial No. of the Location shown in the Location List above, which takes

you directly to its menu.

Zone Type setting:

[3]

To review or change the Zone Type setting, press the button, otherwise scroll to the next option.

[4]

The zone type determines how the system handles signals sent from the device. Press and select a

suitable zone type. The list of available Zone Types and the explanation for each zone type is provided below.

Note: As a shortcut, press the 2 digit serial No. of the Zone Type shown in the Location List above, which

takes you directly to its menu.

Chime setting:

[5]

All zones are set to Chime OFF by default. To configure the device to cause the panel to sound (when disarmed)

a Chime melody when tripped, press the button, otherwise scroll to the next option.

Note: For UL Listed Product, the Chime setting must be set to “Chime ON”.

[6]

Select between "Chime OFF", "melody-chime" and "zone name-chime"

. In "melody chime" the control

panel sounds a chime melody when the sensor is tripped. In "zone name-chime" the control panel sounds the

zone name when the sensor is tripped. The chime operates during the Disarm mode only.

Partitions setting:

Note: The "PARTITIONS" menu appears only if Partitions is enabled in the control panel (see section 5.14).

[7] When entering the menu, the display shows the default Partition selection (marked with ).

[8]

Use the keypad keys , , to change the status of the partitions P1, P2 & P3, respectively.

Device Configuration:

[9]

To review or change the Device Configuration (settings), press the button, otherwise scroll to the next

option – see  [5].

[10] To configure the device parameters, refer to its corresponding device datasheet in the device Installation

Instructions. The defaults of the device parameters can be also configured as explained in section 5.4.6.

[11] After completing the configuration of the device, the wizard brings you to the "Next Step" menu with the

following 3 options:

"NEXT Device" to enroll the next device.

"MODIFY Same Dev." reverts to Step 1 (i.e. "LOCATION") to allow you to perform additional changes to the

device, if needed.

"EXIT Enrollment" exits the enrollment procedure and returns to Step 1 bringing you back to the

"02:ZONES/DEVICES" menu.

Location List

No. Location Name

01 Attic

09 Dining room

17 Hall

25 Utility room

02 Back door

10 Downstairs

18 Kitchen

26 Yard

03 Basement

11 Emergency

19 Laundry room

27 Custom 1

04 Bathroom

12 Fire

20 Living room

28 Custom 2

05 Bedroom

13 Front Door

21 Master bath

29 Custom 3

06 Child room

14 Garage

22 Master bedroom

30 Custom 4

Refers to PowerMaster-30 G2 only

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 95 96

Kommentare zu diesen Handbüchern

Keine Kommentare

Visonic POWERMASTER-10 Betriebsanweisung Seite 32

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Visonic POWERMASTER-10